290 DMG MORI maquina usada para la venta

GeneralVertical Machining Center; Control: Control SIEMENS 828D CharacteristicsTable surface850 x 650 mmDimensions (L x W x H)3,07 x 2,67 x 2,84 mRapid feed X / Y / Z24/24/24 m/minMovement X / Y / Z550/550/510 mmSpindle taperSK 40 DIN 69871 Tool Magazine with24 PositionsMax. torque64 NmTorque (100% DC)43 NmDrive power (40% DC)13 kWDrive power (100% DC)9 kWSpeed max.10000 rpmWeight approx.5600 KgSK40 interfaceTool clamping SK 40 for pull-studs DIN 69872

GeneralVertical-Machining centre Stealth Design; Control: CELOS with Siemens 840D sl Operate Technical DataFeed rate longitudinal/transverse/vertical1-42000/1-42000/1-42000 mm/minRapid traverse longitudinal/transverse/vertical42/42/42 m/minWorking area 1Longitudinal1450 mmCross700 mmVertical550 mmTableTable surface 1760 x 750 mmMaximum load (table centre) 2000 KgSlot width 14 mmNumber of Slots 7Distance between T-Slots 100 mmSpindle speed 15,000 rpm, 200NmMotor spindle speedMASTER® HSK-A63 Spindle speed 20 - 15,000 min-1 Output 46 kW / 30 kW (62 hp / 40 hp) Torque 200 Nm / 130 Nm (148 ft lbs / 96 ft lbs) (40 / 100 % duty cycle)Tool magazine 60 pockets HSK-A63Tool magazine 60 pockets HSK-A63 Chain magazine with pockets and with double gripper, incl. manually direct tool loading into the tool magazineInternal coolant supply package 80 bar / 980 lInternal coolant supply package 80 bar / 98 ...

GeneralVertical-Machining centre Stealth Design; Control: CELOS with Heidenhain TNC 640 Technical DataRapid traverse longitudinal/transverse/vertical42/42/42 m/minFeed rate longitudinal/transverse/vertical1-42000/1-42000/1-42000 mm/minWorking area 1Cross700 mmLongitudinal1450 mmVertical550 mmIntegrated motor spindle speedMASTER®Integrated motor spindle speedMASTER® At speeds > 18.000 min-1, the use of tools with dual contact system (BIG-PLUS®) is stipulated.Drive power (100% DC) 25 kWDrive power (40% DC) 35 kWTorque (100% DC) 86 NmTableTable surface 1760 x 750 mmClamping System DIN ISO 7388-3-ADSpindle taper SK40 Tool holder DIN ISO 7388-1-ASpeed range - 20000 rpmTorque (40% DC) 130 NmSlot width 14 mmMaximum load (table centre) 1500 KgNumber of Slots 7Distance between T-Slots 100 mmCabin roofCabin roof In sheet steel design Open and close via front doorSpecial equipmentClamping pneuma ...

GeneralVertical Machining Center; Control: Control SINUMMERIK ONE CharacteristicsTable surface850 x 650 mmDimensions (L x W x H)3,07 x 2,67 x 2,84 mRapid feed X / Y / Z24/24/24 m/minMovement X / Y / Z550/550/510 mmSpindle taperSK 40 DIN 69871 Tool Magazine with24 PositionsMax. torque64 NmTorque (100% DC)43 NmDrive power (40% DC)13 kWDrive power (100% DC)9 kWSpeed max.10000 rpmWeight approx.5600 KgSK40 interfaceTool clamping SK 40 for pull-studs DIN 69872Electronic HandwheelExternal electronic HandwheelSpecial equipment4th. axis Lehmann

GeneralVertical-Machining centre Stealth Design; Control: CELOS X with Siemens 840D SL Operate CharacteristicsTable surface1460 x 750 mmMaximum load (table centre)1500 KgTool Magazine with40 PositionsMovement X / Y / Z1150/700/550 mmRapid feed X / Y / Z42/42/42 m/minWeight approx.12900 KgSpindle speed 20 - 12,000 rpm SK50, 288NmSpindle speed 20 - 12.000 rpm SK50 for tool taper according to DIN ISO 7388-1-A50 with power 44/32 kW // 59.0/42.9 hp with torque 288/187 Nm (40/100% DC) (differently from standard)Tool magazine 40 pocketsTool magazine 40 pockets SK50 chain magazine with pockets and double gripper, incl. manually direct loading into the tool magazineCoolant-air blast change-overCoolant - Air-blast changeover external switchable via M-FunctionAir blast through spindle centreAir blast through spindle centre activated by M function, maintained air with low oil rateInternal coolant su ...

GeneralVertical machining center in C-frame-design New DMG MORI Design Direct Measuring system X,Y,Z; Control: CELOS with Heidenhain TNC 640 Technical DataFeed rate longitudinal/transverse/vertical1-42000/1-42000/1-42000 mm/minRapid traverse longitudinal/transverse/vertical42/42/42 m/minWorking area 1Longitudinal650 mmCross520 mmVertical475 mmTool changerType of magazineChain Type of gripperDouble gripper Number of tools30 TableTable surface 960 x 570 mmMaximum load (table centre) 800 KgSlot width 14 mmNumber of Slots 5Distance between T-Slots 100 mmSpindle speed 15,000 rpm, 200 NmMotor spindle speedMASTER® SK 40 Spindle speed 20 - 15,000 min-1 Output 46 kW / 30 kW (62 hp / 40 hp) Torque 200 Nm / 130 Nm (148 ft lbs / 96 ft lbs) (40 / 100 % duty cycle) BIG-PLUS® tools possibleTool magazine 30 pockets SK40Tool magazine 30 pockets SK40 Chain magazine with pockets and with double gripper,  ...

GeneralVertical machining center in C-frame-design New DMG MORI Design Direct Measuring system X,Y,Z; Control: CELOS with Siemens 840D sl Operate Technical DataFeed rate longitudinal/transverse/vertical1-42000/1-42000/1-42000 mm/minRapid traverse longitudinal/transverse/vertical42/42/42 m/minWorking area 1Cross520 mmLongitudinal650 mmVertical475 mmTool changerType of magazineChain Type of gripperDouble gripper Number of tools60 TableTable surface 960 x 570 mmMaximum load (table centre) 800 KgSlot width 14 mmNumber of Slots 5Distance between T-Slots 100 mmSpindle speed 20.000 rpmMotor spindle speedMASTER® HSK-A63 Spindle speed 20 - 20,000 min-1 Output 35 kW / 25 kW (47 hp / 33 hp) Torque 130 Nm / 86 Nm (96 ft lbs / 63 ft lbs) (40 / 100 % duty cycle)Tool magazine 60 pockets HSK-A63Tool magazine 60 pockets HSK-A63 Chain magazine with pockets and with double gripper, incl. manually direct t ...

CharacteristicsTable surface1460 x 750 mmMaximum load (table centre)1500 KgTool Magazine with30 PositionsMovement X / Y / Z1150/700/550 mmRapid feed X / Y / Z42/42/42 m/minWeight approx.12900 KgGeneralVertical-Machining centre Stealth Design; Control: CELOS X with Siemens 840D SL Operate Spindle speed 15,000 rpm, 200 NmMotor spindle speedMASTER® SK 40 Spindle speed 20 - 15,000 min-1 Output 46 kW / 30 kW (62 hp / 40 hp) Torque 200 Nm / 130 Nm (148 ft lbs / 96 ft lbs) (40 / 100 % duty cycle) BIG-PLUS® tools possibleTool magazine 30 pockets SK40Tool magazine 30 pockets SK40 Chain magazine with pockets and with double gripper, incl. manually direct loading into the tool magazineCoolant-air blast change-overCoolant - Air-blast changeover external switchable via M-FunctionAir blast through spindle centreAir blast through spindle centre activated by M function, maintained air with low oil rat ...

GeneralVertical Machining Centres; Control: DMG MORI SLIMline® Multi-Touch control CharacteristicsMaximum load (table centre)800 KgDimensions (L x W x H)3,3 x 2,7 x 2,94 mRapid feed X / Y / Z30/30/30 m/minMovement X / Y / Z800/560/510 mmSpindle taperSK 40 DIN 69871 Tool Magazine with30 PositionsMax. torque83 NmTorque (100% DC)57 NmDrive power (40% DC)13 kWDrive power (100% DC)9 kWSpeed max.12000 rpmTable surface1100 x 560 mmWeight approx.5550 KgDirect measuring system X,Y,ZDirect Measuring System X, Y, Z inclusive Air Purge for Measuring SysteminlineMASTER® spindle 12.000 rpminlineMASTER® spindle 12.000 rpm Spindle speed range 20 to 12.000 rpm Tool Taper SK40 DIN69871 with BIG PLUS inteface Tool clamping according to DIN69872 Power: 13kW (40% DC) / 9kW (100% DC) Torque: 83 Nm (40% DC) / 57 Nm (100% DC) bearings oil-air lubrSK40 interfaceTool clamping SK 40 for pull-studs DIN 69872NC-D ...

GeneralTwo spindle turning/milling centre with - Main and counter spindle; Control: CELOS with Siemens 840D sl Operate Tool holder 2Number of tool stations12 Shank diametre according to DIN 6988040 mmNumber of driven tools12 Speed max.4000 rpmPower max. (40% DC)10 kWTool magazineMax. tool length230 mmNumber of tools24 Max. tool diameter80 mmMax. tool weight7 KgTurning-milling spindleSpindle taperHSK-A 63 Spindle speed-12000 rpmDrive power (100% DC)19 kWDrive power (40% DC)22,5 kWTorque (100% DC)85 NmTorque (40% DC)120 Nmlocking moment1000 NmSwivelling range+/-110 degreeSlide 3Longitudinal stroke1200 mmSlide 2Longitudinal stroke1200 mmTransverse stroke195 mmSlide 1Longitudinal stroke1200 mmTransverse stroke490 mmY axis, vertical+/- 100 mmHeadstock, rightClamping chuck Ø315 mmSpindle nose diameter170h5 mmSpindle bore87 mmSpindle diametre on front bearing130 mmDrive power (100% DC)25 kWDri ...

GeneralCNC Turning Centre; Control: Control M730UM with CELOS CharacteristicsMax machining diameter406 mmDimensions (L x W x H)3,35 x 2,11 x 2,2 (3,99 x 2,11 x 2,2) mDrive power main spindle22/18,5 kWRapid feed X / Z30/30 m/minMovements X / Z260/795 mmRotary tool spindle speed10000 rpmNumber of tool stations12 Speed max.2500 rpmBar diameter max.102 mmSpindle bore111 mmMax. Turning Length705 mmWeight approx.6400 KgCELOS - ERGOline TouchCELOS - ERGOline Touch to facilitate machine operation incl. 21.5 ERGOline Touch ® control with multi touch screens Uniform management, documentation and visualization of order, process - and machine data Networkable with CAD / CAM User friendly and pLeft Spindle through-spindle hole dia. 111 mm (spindle speed 2,500 min-1, 22/ 18.5 kW)(Left Spindle) Through-Spindle Hole Dia. 111 mm (4.37-inch) (Spindle Speed 2,500 min-1, 22/18.5 kW) The NLX 2500 adopts a h ...

General2-axes universal turning center with driven tools, C-axis and Y-axis; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over bed650 mmSwing diameter over X linear guideways370 mmMax machining diameter320 mmClamping chuck Ø250 mmX travel250 mmY travel+/-50 mmZ travel550 mmDistance between spindle noses800 mmMain drive 1Type of main driveAC Drive power (100% DC)12,6 kWDrive power (40% DC)14 kWSpeed range-5500 rpmTorque (100% DC)171 NmC-Axis Speed100 rpmMax. torque (40% DC)192 NmTorque of C-Axis (holding torque)168 NmWork spindleSpindle diametre on front bearing120 mmSpindle noseA2-6 Spindle bore73 mmBar diameter max.65 mmTool holder 1Number of tool stations12 Number of driven tools12 Speed max.6000 rpmPower max. (40% DC)4,6 kWDMG MORI IoTconnectorIoTconnector connects DMG MORI machines as well as third-party machines with CELOS. Standardized interfaces enable d ...

General2-axis universal turning machine with - partiall hollow clamping device (hydr.) inner draw tube Ø 52 mm - C-axis and spindle brake (hydr.) - 12 stations circle revolver Sauter reception acc. VDI 30, DIN 69880-30 with tool drive Connection/drive acc. DIN 5480 Direct measuring system, glas scale in X-axis - tailstock; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways500 mmTransverse stroke190 mmLongitudinal stroke525 mmClamping chuck diameter max.210 mmWork spindle (left)Spindle noseFlat flange Spindle bore73 mmDiametre of spindle nose140h5 mmSpindle diametre on front bearing100 mmMain drive 1Drive power (100% DC)13 kWSpeed range20 - 6000 rpmTorque (100% DC)171 NmC-Axis Speed-300 rpmTorque of C-Axis (holding torque)192 NmTool holder 1Number of tool stations12 Shank diametre according to DIN 6988030 mmNumber of driven tools12 Speed max.-500 ...

General2-axes universal turning center with driven tools, C-axis and Y-axis; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over bed650 mmSwing diameter over X linear guideways370 mmMax machining diameter320 mmClamping chuck Ø250 mmX travel250 mmY travel+/-50 mmZ travel550 mmDistance between spindle noses800 mmMain drive 1Type of main driveAC Drive power (100% DC)12,6 kWDrive power (40% DC)14 kWSpeed range-5500 rpmTorque (100% DC)171 NmMax. torque (40% DC)192 NmC-Axis Speed100 rpmTorque of C-Axis (holding torque)168 NmWork spindleSpindle noseA2-6 Spindle diametre on front bearing120 mmSpindle bore73 mmBar diameter max.65 mmTool holder 1Number of tool stations12 Speed max.6000 rpmNumber of driven tools12 Power max. (40% DC)4,6 kWDMG MORI IoTconnectorIoTconnector connects DMG MORI machines as well as third-party machines with CELOS. Standardized interfaces enable d ...

General2-axes universal turning center with driven tools, C-axis and Y-axis; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over bed650 mmSwing diameter over X linear guideways370 mmMax machining diameter320 mmClamping chuck Ø250 mmX travel250 mmY travel+/-50 mmZ travel550 mmDistance between spindle noses800 mmMain drive 1Type of main driveAC Drive power (40% DC)14 kWDrive power (100% DC)12,6 kWSpeed range-5500 rpmTorque (100% DC)171 NmC-Axis Speed100 rpmMax. torque (40% DC)192 NmTorque of C-Axis (holding torque)168 NmWork spindleSpindle noseA2-6 Spindle diametre on front bearing120 mmSpindle bore73 mmBar diameter max.65 mmTool holder 1Number of tool stations12 Number of driven tools12 Speed max.6000 rpmPower max. (40% DC)4,6 kWDMG MORI IoTconnectorIoTconnector connects DMG MORI machines as well as third-party machines with CELOS. Standardized interfaces enable d ...

General2-axes universal turning center with driven tools, C-axis and Y-axis; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over bed650 mmSwing diameter over X linear guideways370 mmMax machining diameter320 mmClamping chuck Ø250 mmX travel250 mmY travel+/-50 mmZ travel550 mmDistance between spindle noses800 mmMain drive 1Type of main driveAC Drive power (100% DC)12,6 kWDrive power (40% DC)14 kWSpeed range-5500 rpmTorque (100% DC)171 NmMax. torque (40% DC)192 NmC-Axis Speed100 rpmTorque of C-Axis (holding torque)168 NmWork spindleSpindle noseA2-6 Spindle diametre on front bearing120 mmSpindle bore73 mmBar diameter max.65 mmTool holder 1Number of tool stations12 Number of driven tools12 Speed max.6000 rpmPower max. (40% DC)4,6 kWDMG MORI IoTconnectorIoTconnector connects DMG MORI machines as well as third-party machines with CELOS. Standardized interfaces enable d ...

Working areaSwing diameter over bed650 mmSwing diameter over X linear guideways370 mmMax machining diameter320 mmClamping chuck Ø250 mmX travel250 mmY travel+/-50 mmZ travel550 mmDistance between spindle noses800 mmGeneral2-axes universal turning center with driven tools, C-axis and Y-axis; Control: CELOS with Siemens 840D sl Operate Main drive 1Type of main driveAC Drive power (100% DC)12,6 kWDrive power (40% DC)14 kWSpeed range-5500 rpmTorque (100% DC)171 NmMax. torque (40% DC)192 NmC-Axis Speed100 rpmTorque of C-Axis (holding torque)168 NmTool holder 1Number of tool stations12 Number of driven tools12 Speed max.6000 rpmPower max. (40% DC)4,6 kWWork spindleSpindle noseA2-6 Spindle diametre on front bearing120 mmSpindle bore73 mmBar diameter max.65 mmDMG MORI IoTconnectorIoTconnector connects DMG MORI machines as well as third-party machines with CELOS. Standardized interfaces enable d ...

General2-axes universal turning center with driven tools, C-axis and Y-axis; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over bed650 mmSwing diameter over X linear guideways370 mmMax machining diameter320 mmClamping chuck Ø250 mmX travel250 mmY travel+/-50 mmZ travel550 mmDistance between spindle noses800 mmMain drive 1Type of main driveAC Drive power (100% DC)12,6 kWDrive power (40% DC)14 kWSpeed range-5500 rpmTorque (100% DC)171 NmMax. torque (40% DC)192 NmC-Axis Speed100 rpmTorque of C-Axis (holding torque)168 NmWork spindleSpindle noseA2-6 Spindle diametre on front bearing120 mmSpindle bore73 mmBar diameter max.65 mmTool holder 1Number of tool stations12 Number of driven tools12 Speed max.6000 rpmPower max. (40% DC)4,6 kWDMG MORI IoTconnectorIoTconnector connects DMG MORI machines as well as third-party machines with CELOS. Standardized interfaces enable d ...

General2-axes universal turning center with driven tools, C-axis and Y-axis; Control: CELOS with Siemens 840D sl Operate Main drive 1Type of main driveAC Drive power (100% DC)12,6 kWDrive power (40% DC)14 kWSpeed range-5500 rpmTorque (100% DC)171 NmMax. torque (40% DC)192 NmC-Axis Speed100 rpmTorque of C-Axis (holding torque)168 NmWorking areaSwing diameter over bed650 mmSwing diameter over X linear guideways370 mmMax machining diameter320 mmClamping chuck Ø250 mmX travel250 mmY travel+/-50 mmZ travel550 mmDistance between spindle noses800 mmWork spindleSpindle noseA2-6 Spindle diametre on front bearing120 mmSpindle bore73 mmBar diameter max.65 mmTool holder 1Number of tool stations12 Number of driven tools12 Speed max.6000 rpmPower max. (40% DC)4,6 kWDMG MORI IoTconnectorIoTconnector connects DMG MORI machines as well as third-party machines with CELOS. Standardized interfaces enable d ...

General2-axis universal turning machine with - partiall hollow clamping device (hydr.) inner draw tube Ø 52 mm - C-axis and spindle brake (hydr.) - 12 stations circle revolver Sauter reception acc. VDI 30, DIN 69880-30 with tool drive Connection/drive acc. DIN 5480 Direct measuring system, glas scale in X-axis - tailstock; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways500 mmTransverse stroke210 mmLongitudinal stroke525 mmClamping chuck diameter max.210 mmMain drive 1Drive power (100% DC)13 kWSpeed range20 - 6000 rpmTorque (100% DC)171 NmC-Axis Speed-300 rpmTorque of C-Axis (holding torque)192 NmWork spindle (left)Spindle noseFlat flange Diametre of spindle nose140h5 mmSpindle bore73 mmSpindle diametre on front bearing100 mmTool holder 1Number of tool stations12 Shank diametre according to DIN 6988030 mmNumber of driven tools12 Speed max.-500 ...

GeneralCNC Turning Centre; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways710 mmClamping chuck diameter max.315 mmLongitudinal stroke1345 mmTransverse stroke260 mmWork spindle (left)Spindle bore91 mmSpindle diametre on front bearing140 mmMain drive 1Drive power (100% DC)22 kWSpeed range- 4000 rpmTorque (100% DC)410 NmMax. torque (40% DC)525 NmAccuracy at point stopping0,001 degreeTool holder 1Number of tool stations12 Shank diametre according to DIN 6988040 mmNumber of driven tools12 Speed max.-6000 rpmPower max. (100% DC)10 kWFloor space/WeightWeight approx.7800 KgDimensions (L x W x H)5,4 x 2,07 x 2,6 mPlug-in board with 2x4 free in-/outputsInputs / outputs programmable via M-functions, consisting of: 8 inputs 4 outputs, 2 amperes 4 outputs, potential-freeExcentric turning and milling operationExcentric turning and milling operation (only with Sie ...

General2 spindles automatic lathe - 2 cross slides - Main and counter spindle - Y axis on slide 1 - Y axis on slide 2 - C axis on main spindle - C axis on counter spindle - Chip tank with coolant system and coolant pump - Part unloading chute; Control: Numeric control Fanuc 32i Working areaBar diameter max.20 mmCounter spindle collet cleaningCounter spindle collet cleaning with coolantChanging kit from steady to sliding headstockChanging kit from steady to sliding headstock including application bush type Dunner B260 and bush-spindle syncronismAdditional charge for belt type chip conveyorAdditional charge for belt type chip conveyor, compatible with shaft-unloading-device Specific chip removol systems (for example: scraping blades chip conveyors, with additional filtering systems) are recommended in case of short chip material machininOil mist filter for emulsion or oilOil mist filter fo ...

The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 730 mm y-travel: 730 mm z-travel: 880 mm total power requirement: 46 kW weight of the machine ca.: 15 t required space: 5.5x3.0x2.8 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

GeneralCNC Turning Centre; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways620 mmTransverse stroke260 mmLongitudinal stroke795 mmClamping chuck diameter max.315 mmWork spindle (left)Spindle bore91 mmSpindle diametre on front bearing140 mmMain drive 1Drive power (100% DC)22 kWSpeed range- 4000 rpmTorque (100% DC)410 NmMax. torque (40% DC)525 NmAccuracy at point stopping0,001 degreeTool holder 1Number of tool stations12 Shank diametre according to DIN 6988040 mmNumber of driven tools12 Speed max.-6000 rpmPower max. (100% DC)10 kWFloor space/WeightDimensions (L x W x H)3,99 x 2,03 x 2,2 mWeight approx.6500 KgTechnologie cycle alternating speedTechnology cycle for the application of an alternating speed for vibration sensitive set-ups (Only in conjunction with Siemens control)Chuck rinsing device, outsidechuck rinsing device, outside (main spindle)Main s ...

General- Compound slides with turning/milling spindle as integrated spindle motor, with hydr. locking at turning acceptance HSK-63A DIN 69893 - Y-axis ± 125 mm - B-axis ±120° with pneumatic locking - Tools magazin disc with 1x24 positions - Absolute direct gauging system in the X, Y, Z linear axes - Coolant pump 12 bar; 23l/min - Cooling system for spindle motor, turning/milling spindle, B-axis torque motor; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways500 mmMax. Turning Length1200 mmTurning diameter500 mmBar diameter max.65 mmWork spindle (left)Spindle noseFlat flange Diametre of spindle nose170h5 mmSpindle bore87 mmSpindle diametre on front bearing130 mmMain drive 1Drive power (100% DC)25 kWDrive power (40% DC)32 kWSpeed range- 5000 rpmTorque (100% DC)280 NmMax. torque (40% DC)360 NmTurning-milling spindleSpindle taperHSK-A 63 DIN 69893 ...

Working areaSwing diameter over guide ways500 mmTurning diameter500 mmMax. Turning Length1200 mmBar diameter max.65 mmGeneral- Compound slides with turning/milling spindle as integrated spindle motor, with hydr. locking at turning acceptance HSK-63A DIN 69893 - Y-axis ± 125 mm - B-axis ±120° with pneumatic locking - Tools magazin disc with 1x24 positions - Absolute direct gauging system in the X, Y, Z linear axes - Coolant pump 12 bar; 23l/min - Cooling system for spindle motor, turning/milling spindle, B-axis torque motor; Control: CELOS with Siemens 840D sl Operate Work spindle (left)Spindle noseFlat flange Diametre of spindle nose170h5 mmSpindle bore87 mmSpindle diametre on front bearing130 mmMain drive 1Drive power (100% DC)25 kWDrive power (40% DC)32 kWSpeed range- 5000 rpmTorque (100% DC)280 NmMax. torque (40% DC)360 NmTurning-milling spindleSpindle taperHSK-A 63 DIN 69893 ...

GeneralTwo spindle Swiss turning automatic lathe; Control: Fanuc 310is Working areaBar diameter max.42 mmChanging kit from steady to sliding headstockChanging kit from steady to sliding headstock including application bush type Dunner B236 and bush-spindle syncronismDrive for support for back workingDrive for support for back working operation (slide 2) power 0.55 KWAxial drilling unit for back work.oper.Axial drilling unit for support for back working operation (slide 2) with 2 rot.spindles, junction for collet ESX/ER 20 and 2 cyl.junction diam.25mmDouble tool h. for ext.machining on rev.Double tool holder for external machining on revolver for shaft 16x16Double drill hold. on rev.cyl.junct.d.25Double drill holder on revolver with cyl. junction diam.25mmRad.driven mill.-drill.unit on rev.Radial driven milling and drilling unit on revolver with junction for collet ESX/ER 20 ratio 1:1 sp ...

GeneralCNC Swiss type lathe with Fanuc control; Control: FANUC 310 iTB Working areaTurning diameter33 mmSpecial equipmentHinged belt chip conveyor with Discharge height 1200 mm Aut. bar feeder IEMCA BOSS 545/32 E, max_ L=3200 mm, incl. guide channel diam. 18 mm

GeneralIntegrated Mill Turn Center; Control: Control F31iB5 with CELOS CharacteristicsSwing- Ø, max.700 mmMilling spindle upper side1 Bar diametre80 mmSpeed max.4000 rpmMax. Turning Length1530 mmMax machining diameter670 mmDrive power tool spindle5,5/3,7 kWDrive power milling spindle28/23 kWDrive power main spindle18,5/15 kWMovements X / Z200/1542 mmLower Turret10 PositionsNumber of Toolmagazine positions38 Speed max.12000 rpmSlewability of B-Axis±120 degreeMovements X / Z / Y675/1562/300 (±150) mmWeight approx.18500 KgCELOS - ERGOline TouchCELOS - ERGOline Touch to facilitate machine operation incl. 21.5 ERGOline Touch ® control with multi touch screens Uniform management, documentation and visualization of order, process - and machine data Networkable with CAD / CAM User friendly and p(Left Spindle) through-spindle hole dia. 91 mm, 4,000min-1 (STD)(Left Spindle) Through-spindle Hol ...